My entryway console table makeover is finally finished! I already know that people’s opinions will be split on this, but I ended up painting the console table rather than trying to use gel stain to try to preserve a natural wood finish. After looking around the living room and music room (i.e., the two adjoining areas), I realized that I already have a lot of natural wood finishes in these areas, and I’m partial to painted finishes. So I decided to go for it.
I chose a dark-ish green called Scallion from Behr. I went with green instead of pink for two reasons. First, I had already spent time doing a makeover on my lamps using art pastels (you can read more about that here) and it took a while to get the color exactly what I wanted. I wasn’t willing to repaint those. But the main reason is because when I stood back and looked at the whole area, I realized that a big pink piece of furniture in the entryway would probably compete for attention with the raspberry-colored settee in the music room, and both are very visible as soon as one enters the front door of our house. So, green was the color.
For some reason, the colors of both the console table and the lamps look brighter in pictures. They’re both a little darker in person. But anyway, here’s the final result.
I’m still going to add some accessories and finishing touches to the area, but at least the main pieces are finally finished.
So let me back up and remind you where this started. Here’s how the console table looked before its makeover. I know a lot of you really loved the natural wood finish on it, but the finish really bothered me. It might look fine in pictures, but in person, it was way too orange and splotchy for my taste. I’ve lived with it for a long time like this, and I finally decided that I didn’t want to live with this streaky, splotchy finish anymore.
So since I was giving it a makeover anyway, I decided to take the advice that some of you had and get rid of the lower shelf. Once I removed the shelf, I had four turned legs that were each in two parts.
I glued and nailed those together and then used wood filler to fill the crack where the two pieces met.
And then I needed to add a block at the top so that I could attach the legs securely to the upper part of the console table. Using a hand saw, I cut off the top turned section of each leg.
And then I used the top smooth end of that turned section to trace a circle on the blocks that I made by gluing and nailing four 2×2’s together.
Here’s what that looked like with the circle traced on the top of the block.
Next, I used my orbital sander with an 80-grit sanding disc to sand down the corners at an angle until I reached the edge of the traced circle.
Here’s what that looked like from the side…
Once I had the corners sanded down, I started sanding all the way around, keeping that same angle with my sander, until the whole thing was sanded to meet the edges of the circle.
And then I did a little more detail sanding to round off those bottom corners and blend them in with the side edges on the block.
Once I had them sanded, I attached those blocks to the legs using wood glue and 18-gauge 1.5-inch nails. (The block shown here hadn’t been completely sanded yet, and it isn’t actually attached yet.)
With my new Frankenstein legs completed, I attached them to the bottom of the console table using a whole lot of wood glue and a few 16-gauge 2-inch nails toenailed in from each side.
Once all four were attached, I left them alone for a while so that the wood glue could dry.
Next, I cut lengths of 2×2 lumber and attached them between the legs. I didn’t have enough 2×2 lumber on hand to reach the full span between the back legs, so I just used smaller pieces and made sure they were firmly against the block on the back legs. I attached those 2×2 pieces of lumber with lots of wood glue and then 2.5-inch 16-gauge nails to secure them to the bottom of the console table.
And finally, I used 2.5-inch wood screws and angled them in so that they would go through the 2×2 lumber and into the sides of the blocks on the legs.
I was going to use my Kreg pocket hole jig for this, but as I was trying to adjust the drill bit for the right depth, I accidentally unscrewed the little screw on the collar of the drill bit too much and it came out all the way. And then it fell on the floor and I couldn’t find it. So I had to make do without my handy Kreg pocket hole jig and just angle the screws in without those clean pocket holes. It worked out fine in the end, but it would have been a whole lot easier with pocket holes. Drilling pocket holes first minimizes the risk (there’s pretty much zero risk) of the screw splitting the wood as it’s going in.
Here’s what it looked like once it was flipped upright. I definitely like it better without the shelf, and as I’ve already learned, it’s a whole lot easier to clean underneath the console table without that low shelf in the way. But I still needed to cover the edges with trim.
I forgot to take a picture of the trim before I painted the console table, but I found a 2 1/4-inch trim at Lowe’s that worked perfectly to attach to the bottom and cover over the 2×2 lumber and the area where that 2×2 met the bottom of the console table.
Now that it’s all said and done, I’m really glad I took the time to remove that bottom shelf. I really like the more open look. And as I said, it’s so much easier to clean under the console table now.
I swapped out the ring pulls for some very simple large gold knobs. I was ready for a change there, too. I like the simplicity of these.
I’m not sold on the items that are currently in the middle of the console table, but I had these on hand, so I put them there for now. I’ll see what else I can come up with. Or maybe I won’t. I’m not sure yet. But I do have some ideas for the areas on each side of the console table. I think those areas need a little something.
I’m glad to finally have this done, and I’m really glad that I found a way to keep the turned legs. I don’t think I would have been satisfied with those simple, straight legs that I previously considered. And now that this is done, I need to finish up with some accessories, get all of my tools cleared away, and get the living room back in order. And then I’ll show you the whole area with the new look of the entryway wall.
Addicted 2 Decorating is where I share my DIY and decorating journey as I remodel and decorate the 1948 fixer upper that my husband, Matt, and I bought in 2013. Matt has M.S. and is unable to do physical work, so I do the majority of the work on the house by myself. You can learn more about me here.
Trending Products
